Up
Previous Next

Sheriff CSM™

Deploying HIDS to Servers

We recommend deploying a host-based intrusion detection system (HIDS) to enable

• File integrity monitoring
• Rootkit detection
• Event log collection

The Getting Started Wizard provides two options for HIDS agent deployment.

Windows — HIDS agent is installed locally on specified hosts. All Windows hosts must meet the prerequisites described in the Asset Management topic, Deploying HIDS Agents, of the Sheriff CSM User Guide.

UNIX/Linux — HIDS agents are not installed on hosts but provide agentless operation. UNIX and Linux systems are monitored remotely for file integrity only. For information on installing HIDS agents on UNIX/Linux hosts, see Deploy the Sheriff HIDS Agents to Linux Hosts.

Before you can deploy a HIDS agent to the Windows machine, make sure that it meets the following requirements.

• If using any network accelerator devices in the environment, you must add Sheriff CSM Sensor (Deputy) to their whitelist. This is because the Sheriff CSM Sensor utilizes SMB (Server Message Block) to transfer the HIDS agent installation package to the Windows machine. If the network accelerator tries to optimize the traffic from the Sheriff CSM Sensor, it may cause the HIDS deployment to fail.

• The operating system must be one of the following

  • Microsoft Windows XP
  • Windows 7, 8, or 10
  • Windows Server 2003, 2008R2, or 2012R2

• You need to use a user account that belongs to the same Administrators group as the local Administrator account.

  Note: For security reasons, the local Administrator account is disabled by default on all versions of Windows currently in mainstream support. In order for the HIDS deployment to succeed, you need to enable the local Administrator account (not recommended), or create a user account and add it to the built-in Administrators group.

• You must have changed the target Windows machine based on the steps below.

  To change the settings on Windows XPTo change the settings on Windows XP

  1. Go to Control Panel > Folder Options > View.

  2. Deselect Use simple file sharing.

  3. Go to Control Panel > Windows Firewall > Exceptions.

  4. Select File and Printer Sharing.

  To change the settings on Windows 7To change the settings on Windows 7

  1. Go to Control Panel > Folder Options > View.

  2. Deselect Use Sharing Wizard (Recommended).

  3. Go to Control Panel > System and Security > Windows Firewall > Advanced Settings > Inbound Rules.

  4. Enable File and Printer Sharing (SMB-In).

  5. Go to Control Panel > User Accounts > Change User Account Control Settings.

  6. Move the slider to Never notify.

  To change the settings on Windows Server 2003, 2008 R2, and 2012 R2To change the settings on Windows Server 2003, 2008 R2, and 2012 R2

  1. Go to Control Panel > Windows Firewall > Advanced Settings > Inbound Rules.

  2. Enable File and Printer Sharing (SMB-In).

  3. To allow NTLMv2 security, run gpedit.msc.

  4. Go to Local Security > Computer Configuration > Windows Settings > Security Settings > Local Policies > Security Options and change these settings.

     1. Network Security: Minimum session security for NTLMSPP based (including secure RPC) clients, select

        • Require NTLMv2 session security
        • Require 128-bit encryption

     2. Network Security: Minimum session security for NTLMSPP based (including secure RPC) servers , select

        • Require NTLMv2 session security
        • Require 128-bit encryption

     3. Network Security: LAN Manager Authentication level , select

        • Send NTLMv2 response only\refuse LM & NTLM

  To change the settings on Windows 8 and 10To change the settings on Windows 8 and 10

  1. Go to Control Panel > Folder Options > View.

  2. Deselect Use Sharing Wizard (Recommended).

  3. Go to Control Panel > System and Security > Windows Firewall > Advanced Settings > Inbound Rules.

  4. Enable File and Printer Sharing (SMB-In).

  5. Enable Windows Management Instrumentation (WMI) entry.

  6. Go to Control Panel > User Accounts > Change User Account Control Settings.

  7. Move the slider to Never notify.

  8. Open Group Policy.

     1. Go to Local Policies > Security Options
     2. Network access: Shares that can be accessed anonymously to IPC.
     3. Set User Account Control: Run all administrators in Admin Approval Mode to Disabled (recommended).

  9. Apply changes and restart the machine.

Note: The Winexe installation utility may trigger a false positive alert as a “potential hacking tool” during an authorized application installation, even though the Winexe remote installation is an authorized action. In this instance, the best practices are to either whitelist the IP address of Sheriff CSM, or temporarily disable the antivirus software during the installation.

To deploy HIDS

1. Select the Windows or the UNIX/Linux tab, as appropriate.

2. Type your Username and Password.

   Note: For UNIX/Linux systems, this should be your SSH credentials.

3. (Windows only) Optionally, enter the Domain information.

4. From the asset tree on the right, choose the asset(s) on which you would like to deploy a HIDS agent.

5. Click Deploy.

   The HIDS Deployment popup prompts you for confirmation

6. Click Continue.

   A progress bar appears.

   After the deployment finishes, a message displays the number of devices successfully deployed with HIDS.

7. Click OK.

   

8. After you finish deploying the HIDS agents, click Next at bottom-right to proceed.